Dual LED Battery-Powered Wireless Indoor/Outdoor Motion Lights

The Lumenology Dual Motion Light provides an impressive 1000 Lumens from two, high-luminance white LED bulbs. Install the light virtually anywhere with the adjustable bracket or clamp. The IP44 Water Resistant rating equips it for outdoor use, even in the elements. MotionSense Technology provides a 20 ft detectable range and 140-degree field-of-view, which will detect motion in both dark and light environments with the built-in LightSense Technology.IncludesOne (1) Lumenology Dual Security Motion Light in White or BronzeOne (1) clampOne (1) L-rodOne (1) butterfly nutOne (1) plastic capFour (4) plastic anchorsFour (4) screwsUser manualFeaturesUltra-bright two-headed LED motion light provides powerful 1000 Lumens of white light that will instantly improve a home’s securityThe 360° adjustable heads customize the light coverage to suit any environmentThe 20ft detectable range and 140-degree field-of-view detects motion in dark and light environmentsThree user modes: Motion activated 10-second, 20-second, or 30-second with auto shut-offCan be installed on a ceiling, wall, railing, tree, and moreNo electricity or wiring requiredGreat for use indoors and outdoors, even in the elementsIP44 water resistantHigh-luminance white lightColor temperature: 5800 KBeam distance: 144 ftLED battery: 3x D Dry Cell (not included)Batteries last for approx. 1530 activations (based on 30-second auto shut off) or 7 hours on “stay-on” modeMeasures 11.06" x 3.75" x 5.8"Weighs 1.4 lbsHow to UseSet up:Turn the battery cover thumb screw counterclockwise until the battery cover is detached from the battery box of the Lumenology Dual Security Motion Light and pull awayDisengage the Inner battery cover by pressing down where the inner battery cover is labeled “push” and pull awayNote: The inner battery cover does not disconnect completely. it rotates on a 90° axis. do not push against the inner battery cover when it is open as it may breakInsert 3x D batteries (not included) and be sure to align the positive (+) and negative (-) terminals correctlyCaution: Some equipment using three or more batteries may appear to work properly even if one battery is inserted incorrectly; such usage may lead to battery leakage or rupture that could result in equipment damageRotate the inner battery cover back into place. Push in until it clicks and does not rotate freelyClose the battery box by first aligning the three tabs on the battery cover to the three notches in the battery boxTurn the battery cover downward until completely closedRotate the battery cover thumb screw clockwise until the battery cover is tightened and secured to the battery boxSensor detection range:The motion sensor can detect movement in a max field-of-view of 140° and a max distance of 20 ftNotes:The motion sensor is less likely to detect motion when walking directly towards the unitThe detection area performs best when set to a height of 6.5 ft (2 m) highInstallation:Using Bracket:Measure, locate, and mark where the Lumenology Dual Security Motion Light will be installedNote: It is recommended to install the Lumenology Dual Security Motion Light directly to a wooden stud, metal stud or plywood wall sheathingPlace the Mounting Bracket on the spot marked in step 1Using a pencil, mark the location through the 4 mounting holes as shownWood stud, metal stud, or plywood wall sheathing: Fasten the mounting bracket directly to the wall with the 4 included screws. No additional anchors are necessaryDry Wall Without Stud:Remove the mounting bracket to expose the marks made in step abovePre-drill 1/8” holes at each of the marked locationsInsert an Anchor into each drilled hole from the previous steps. You may need to lightly hammer the anchors in placePlace the mounting bracket to align the mounting holes with the anchorsFasten the Lumenology Dual Security Motion Light to wall with the 4 supplied ScrewsConcrete:Remove the mounting bracket to expose the previously made marksPre-drill 1/4” holes at each of the marked locationsInsert an anchor into each drilled hole from the previous step You may need to lightly hammer the anchors in placePlace the mounting bracket to align the mounting holes with the anchorsFasten the Lumenology Dual Security Motion Light to wall with the 4 supplied ScrewsUsing clamp:Slide the threaded end of the L-rod through the clampThread the butterfly nut onto the L-rod by rotating clockwise. Do not thread all the way down at this timeAdd plastic cap to the threaded end of the L-rodInsert the flat end of the L-rod into the L-rod slots on the mounting bracketRotate the L-rod 90° to keep the Lumenology Dual Security Motion Light from sliding offPlace the Lumenology Dual Security Motion Light with the hanging surface in-between the clamp and mounting bracketOnce the Lumenology Dual Security Motion Light is in the desired position, continue to thread the butterfly nut clockwise until tight and secureAdjust the LED lights, adjustable arm and motion sensor as shown in the following steps until satisfied with the positioningAdjusting the motion sensor:Grab the Motion Sensor along two sides and rotate left, right, up or down until the preferred positioning is achievedNotes:Do not force any movement as it may cause damage to the motion sensorThe motion sensor will only rotate left / right 160° and up / down 30°Maximum field-of-view: Adjust the motion sensor horizontallyMinimum field-of-view: Adjust the motion sensor diagonally downwardAdjusting the body position:Loosen the adjustment knob by turning counterclockwise and the adjustment arm moves freelyRotate and move the Lumenology Dual Security Motion Light until the desired position is reachedHold and re-tighten the adjustment knob by turning it clockwiseFor additional movement to the adjustable arm, loosen with the bracket-to-arm screw by turning counterclockwise. This will allow the adjustable arm to rotate an additional 160° side-to-side. Once the desired positioning is achieved, re-tighten the Bracket-to-Arm Screw by turning clockwiseNote: For complete adjustment capabilities, loosen the adjustment knob and bracket-to-arm screw at the same timeSetting the mode:Adjust the light sensitivity knob to align the dial to day, night, or somewhere in-between to better suit the surroundings or preferencesDay: LED Light is activated by motion regardless of whether the surrounding area is bright or darkNight: LED Light is only activated by motion when the surrounding area is darkNote: If additional light is preferred in a bright environment, the light sensitivity knob should be moved to the day positionSetting the duration:To adjust the timer, turn the timer knob until the dial aligns with one of the time durations:10s: Once motion is sensed and the LED light is activated, the LED light will remain on for approximately 10-seconds unless motion is detected again20s: Once motion is sensed and the LED light is activated, the LED light will remain on for approximately 20-seconds unless motion is detected again30s: Once motion is sensed and the LED light is activated, the LED light will remain on for approximately 30-seconds unless motion is detected againNote: The angle between durations is not proportional to timeRed LED indicator light:The red LED indicator light will flash at different intervals depending on certain criteria:Blinks once every 5 seconds: Stand-by modeBlinks quickly: Motion sensor is detecting movementBlinks once every second: The batteries are low and the LED Lights will only activate in darknessOff: There are no batteries in the Lumenology Dual Security Motion Light or the batteries need to be replacedNote: The red LED indicator light is easiest viewed in a dark environmentCare InstructionsPlease keep the Lumenology Dual Security Motion Light and all accessories out of reach of small childrenDo not use third party power supplies or non-approved adapters with the Lumenology Dual Security Motion LightDo not attempt to open the outer casing of the Lumenology Dual Security Motion LightDo not clean the Lumenology Dual Security Motion Light with harsh chemicals and keep the Lumenology Dual Security Motion Light away from liquidsDo not expose the Lumenology Dual Security Motion Light to extreme temperaturesDo not paint or apply coatings to the Lumenology Dual Security Motion Light, as you might affect moving parts or damage internal componentsDo not stick foreign objects in any port/opening of the Lumenology Dual Security Motion Light. Doing so may cause electric shockDo not attempt to disassemble or repair the Lumenology Dual Security Motion LightDo not drop the Lumenology Dual Security Motion Light. Doing so may damage internal components otherwise not seen and must not be operatedDo not submerge the Lumenology Dual Security Motion Light or its accessories in waterDisassembling the Lumenology Dual Security Motion Light, including the removal of external screws, may cause damage that is not covered under the warrantyDo not mix new and old batteries. It may cause the LED Light to malfunctionDo not look directly at the LED LightDo not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hybrid) batteriesDo not install the main body in places where large amount of water may come in contact with the Lumenology Dual Security Motion LightDo not use near home electric appliancesDo not install diagonally, downward, or upside down regardless of indoor or outdoor use as it may cause failureDo not install near combustible objectsDo not install near flammable materials such as cloth, paper, or objects that may easily catch fireDo not use manganese, dry, or rechargeable batteries. It may cause a malfunction due to voltage shortageDo not install near appliances emitting radio waves as it may cause failureDo not install near motors or devices generating a magnetic field. May cause failure