Portable LED Battery-Powered Wireless Indoor/Outdoor Motion Light

The Lumenology Portable Motion Light provides a mighty 148 Lumens from a single, high-luminance white LED bulb. Install the light virtually anywhere with the flexible tripod or magnetic base. The MotionSense Technology provides a 13 ft detectable range and 100-degree field-of-view, which will detect motion in a dark environment.IncludesOne (1) Lumenology Portable Motion Light in White or BlackOne (1) flexible tripodOne (1) magnetic plateOne (1) screwOne (1) anchorUser manualFeaturesCompact, lightweight design offers a wireless installation so you can easily grab-and-go when you need itSingle, high-luminance white LED bulb boasts 148 Lumens and can be used virtually anywhere13 ft detectable range and 100-degree field-of-view detects motion in dark environmentsWith a 20-second auto shut-off or always-on mode, this LED light can be utilized where additional light is neededQuick, easy, and versatile to set up and wrap to any fence, deck, pole, and moreGreat for a temporary and non-invasive installationBase can be attached to any magnetic surface or installed with the included magnetic plate to any non-magnetic surface for a more permanent solutionGreat for use indoors and outdoors, even in the elementsIP43 water-resistantHigh-luminance white lightColor temperature: 5700 KBeam distance: 62 ftModes: Off/On/30-Seconds Auto Shut OffDetecting method: Passive infrared sensorLed battery: 3x AA Alkaline (not included)Batteries last for approx. 1000 activations or 7 hours on “stay-on” modeMeasures 3.5” x 3.75” x 4.25”Weighs 6 ozHow to UseSet up:Rotate the main body downward until the LED light is facing the baseRemove the Battery Cover by using your thumb to push inward on the battery cover inset and pull away to remove the battery cover. Insert 3x AA batteries (not included) and be sure to align the positive (+) and negative (-) terminals correctlyCaution: Some equipment using three or more batteries may appear to work properly even if one battery is inserted incorrectly; such usage may lead to battery leakage or rupture that could result in equipment damageClose the battery compartment by aligning the battery cover and pushing firmly to re-attach. You will hear a click when successfulTo use the flexible tripod: Connect the flexible tripod by inserting the threaded attachment to the threaded insert on the base and rotate clockwise to tighten. remove by rotating the flexible tripod counterclockwise until it’s free from the baseStanding: Adjust the legs of the flexible tripod until the Lumenology Portable Motion Light stands to your desired position. Make sure the tripod is standing on level groundHanging:Gently bend the legs of the flexible tripod to wrap around a pole, fence, etc. firmly tighten the legs to assure a sturdy installationNote: For best installation, do not wrap the legs of the flexible tripod in the same direction. Alternate each leg when wrapping them around a bar or fence to insure a safe and successful installationTo use the metal plate and magnet:Fasten the magnetic plate directly to wood or metal stud for the most secure attachmentConcrete: Pre-drill a 1/4” hole and insert the supplied anchor. Place the magnetic plate over the anchor and use the included screw to secureDrywall: Pre-drill a 1/8” hole and insert the supplied anchor. Place the magnetic plate over the anchor and use the included screw to secureAttach the base of the Lumenology Portable Motion Light to the magnetic plate by utilizing the heavy-duty magnets on the bottom of the baseTo detach the Lumenology Portable Motion Light, pull the light away at a slight angle and it will release from the magnetic plateNote: The Lumenology Portable Motion Light can be magnetically attached to any magnetic surface without installation of the magnetic plateTo operate:Move the mode-changing switch to desired setting (auto/off/on) to begin using your Lumenology Portable Motion Light:Auto mode: The unit will be on standby and only illuminate in dark settings when motion is detected within the 13 ft detectable range and 100-degree field-of-view. The light will stay on for 30-seconds unless motion is detected againOff: The light will not activateOn: The light will remain on until the mode changing switch is moved to the off or auto positionNote: The light will not activate in the auto user mode if the surroundings are bright. If additional light is preferred in a bright environment, the mode changing switch should be moved to the on positionCare InstructionsDo not use third party power supplies or non-approved adapters with the Lumenology Portable Motion LightDo not attempt to open the outer casing of the Lumenology Portable Motion LightDo not clean the Lumenology Portable Motion Light with harsh chemicalsDo not paint or apply coatings to the Lumenology Portable Motion Light, as you might affect moving parts or damage internal componentsDo not stick foreign objects in any port/opening of the Lumenology Portable Motion Light. Doing so may cause electric shockDo not attempt to disassemble or repair the Lumenology Portable Motion LightDo not drop the Lumenology Portable Motion Light. Doing so may damage internal components otherwise not seen and must not be operatedDo not submerge the Lumenology Portable Motion Light or its accessories in waterDisassembling the Lumenology Portable Motion Light, including the removal of external screws, may cause damage that is not covered under the warrantyDo not mix new and old batteries. If batteries are not new, it may cause the light to malfunctionDo not look directly at the LED LightDo not bend the arm of the flexible tripod at the same position repeatedly. Doing so may cause the flexible tripod to breakDo not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hybrid) batteries