4. GOLD SEAL - CHLORINATED RUBBER POOL PAINT - 1 GALLON

FOR USE ON CONCRETE & PLASTER UV PROTECTION GREAT COLOR RETENTION/FADE RESISTANCE EASY TO USE PREMIUM GRADE CHLORINATED RUBBER POOL PAINT Gold Seal Chlorinated Rubber Pool Paint GOOD FOR ALL CONCRETE AND PLASTER POOLS Covers approximately 300 square feet per gallon; 2 coats needed for proper application - There is no primer needed - This is a self priming swimming pool paint! Gold Seal Chlorinated Rubber Pool Paint is a long lasting coating designed to provide extended life to your pools surface by utilizing a blend of solids and ultra violet stabilizers which help slow the effect of harmful UV rays. Gold Seal is also designed to offer prolonged protection against chlorine, algae and chemicals and is excellent for new or old concrete and plaster pools. It can be applied over existing acrylic and chlorinated rubber pool paints, as well as bare concrete and plaster surfaces. It dries quickly, is very durable and resists fading. Re-energize your swimming pool today with the "GOLD" standard in the industry, and enjoy it for years to come! EASY TO USE COLORS RETAIN VIBRANCY FOR YEARS DRIES QUICKLY NON-FADING GREAT FOR RE-COATING PREVIOUSLY PAINTED POOLS STRONG UV PROTECTION RESISTANT AGAINST CHLORINE 10 YEAR WARRANTY FOR CONCRETE AND PLASTER POOLS ONLY - *FOR FIBERGLASS, JACUZZI'S OR SPAS, SEE OUR EPOXY POOL PAINTS COLORS: Available in White, Medium Blue, Aqua, Royal Blue, Sky Blue, or Black COVERAGE: Approximate coverage is 300 square feet per gallon. Recommended thickness will require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect less coverage on bare, rough or sandblasted surfaces. To figure out the amount of paint you will require: Length of Pool x Width of Pool x 1.7 = square footage x 2 (2 coats) divided by 300 square feet = gallons needed SURFACE PREPARATION: Power wash or hose the surface to remove all loose paint, dirt, oils, suntan lotions and grease. Clean the pool with a mixture of Tri-Sodium Phosphate (TSP) and water, scrubbing the surface thoroughly, then rinse the area. Next etch the pool with a solution of 50% muriatic acid and 50% water. Then clean again with TSP and flush with plenty of fresh water. Allow to the surface to dry thoroughly for at least 24 hours before beginning application. Glossy surfaces can be power sanded using 80 grit sandpaper if desired. After applying the 1st coat, wait at least 24 hours before applying the 2nd coat. WAIT 5 DAYS AFTER FINAL COAT BEFORE FILLING THE SWIMMING POOL WITH WATER. If it rains at any time during or right after application, add 1 extra day of cure time for each day it rains. SUGGESTED USES: Concrete or plaster swimming pools. For Jacuzzi's, spas, or fiberglass pools, see our Epoxy Pool Paints. FINISH: Glossy. For a more slip resistant finish in areas such as the pool steps or diving platforms, silica sand can be added during application to achieve the desired texture. VEHICLE TYPE: Chlorinated Rubber SOLIDS BY WEIGHT: 60% WEIGHT PER GALLON: 11 lbs. per gallon (varies by color) RECOMMENDED DRY FILM: 4.0 mils VISCOSITY AT 75°F (24°C): 70-80 KU AVERAGE DRY TIME 75°F: Dries to the touch in 12 hours. Lower temperatures & higher humidity will slow down dry times. Second coat can be applied after allowing the first coat a minimum of 24 hours to cure. After applying the second coat, wait 5 days before filling pool the pool with water to allow for a complete cure. If it rains at any time during application, add 1 extra day of cure time for each day of rain. RECOMMENDED REDUCER: If necessary, 3-4 ounces of Xylene can be added to each gallon of paint for easier rollout performance. RESISTANCE TO: Chlorine, Alkali, Algae, Mineral Oils, Fresh and Salt Water RECOMMENDED PRIMERS: This is a self-priming paint. APPLICATION: Brush, Spray or Roller (preferred) Rollers: 1/2” nap mohair, lambskin, or phenolic roller. Keep roller wet. Roll in one direction, re-wet, then cross roll. SPRAY: Conventional Air 50 -70 psi, Tip Size .055 -.070, AIRLESS: 2200-2500 psi, Tip Size .019-.023. POT LIFE: Not Applicable LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 40°F or above 95°F. NOT FOR VINYL LINED OR METAL POOLS. SHELF LIFE: Maximum 9 months MIXING: Mix each gallon either mechanically or by hand for 10 minutes each, then apply as it comes from the container. If necessary, product can be thinned with 3-4 ounces of xylene per each gallon of paint for easier rollout performance. PACKAGE: 1 Gallon Can