Purple Headlight Film With Air Channel Paper Liner

Purple isn't a color you see on every set of headlights, and that's the point. Vinyl Frog's Purple Headlight Film casts a bright, eye-catching violet glow that turns a factory lens into the first thing people notice. It’s vibrant and glossy straight out of the roll, giving the front end a signature, custom look that factory colors can't touch. The film installs wet using a slip solution, giving you the freedom to reposition it until everything is perfectly aligned. As you squeegee out the fluid, the solvent-based acrylic adhesive locks into a strong, lasting bond. The built-in air-release channels help push trapped bubbles out effortlessly, leaving a flat, wrinkle-free finish across curves, corners, and contoured lenses. Once it's down, the film pulls double duty. It blocks the UV that hazes and yellows bare lenses over time, resists scratches and small road debris, and holds its bright violet color through rain, snow, and road spray. A clean, protected lens with a one-of-a-kind finish that doesn't fade after a few washes. Features And Specifications Color: Bright, radiant violet with a glossy finish (VLT TBC) Heat, UV & scratch resistant Weatherproof: holds through rain, snow, and road spray without lifting Wet-application design: slip solution allows for easy repositioning and bubble-free results Repositionable adhesive: slides and resets during wet install, then locks firm Lifetime: about 1 year, rated on vertical-surface exposure Sizes available: 1ft, 2ft, 4ft, 8ft, 16ft, and 32ft. Packaging: Roll. Application: Wet install (slip solution required); warm with a heat gun to conform over sharply curved lenses Best on: headlights, taillights, fog lights, and side markers (check local tint laws) Please Note: This light tint film is semi-transparent. The color may look slightly different on the white backing paper, but once the backing is removed and applied to your lights, you’ll see the true color. Proper Installation If the headlight surface is clean and undamaged before installation, the wrap adheres evenly and removes smoothly. Proper Removal Technique Using gentle heat (like a heat gun or hairdryer) softens the adhesive, making it easier to peel without pulling or tearing the headlight’s factory coating. Warning If the headlights are already oxidized, yellowed, or have weak factory coating, peeling the wrap can pull off clear coat or cause flaking. Video Physical Properties Classification Unit Spec Remark Thickness Top protected film um 25±5 PE Acrylic Adhesive um 20±2 Solvent-based Face Film um 100±5 / Release liner um 180±2% Paper Liner Surface - - Glossy & Matte / Width - cm 30/40±0.01% 1ft/1.3ft Length - m 10±1% 32ft Physical Performance Features Test Method Results Gloss (60°) GB 8807 92.3 VLT / 87% Self-healing Layer Elongation at Break GB/T 1040.1 112 Face Film Elongation at Break GB/T 1040.1 309.5 Tear Strength GB/T529 92.7 KN/m Tensile Strength GB/T 1040.1 21.6 Mpa 100% Modulus GB/T 1040.1 9.1 Mpa Anti-yellowing / ΔE< 1.2 Light Transmission ＞40% 43% Adhesive residue / ＜3% Release force (N/25mm) paste on steel board, 90° 26℃ and 60%, GB2792 0.16 Initial tack (g/25mm) under 24℃ and 26%, GB31125-2014 860 Peel Strength (N/25mm) 180° 15 Holding power(h) paste on steel board, hang on by 25mm*25mm*1kg weight under 29℃ and 55%, GB/T4851-1998 No peel off within 48 hours Aging Test 65℃ and 7 days No adhesive residue under 20 times wrapping Application Temperature / +20℃ to +30℃ Service Temperature / -50℃ to +110℃ Recommended Shelf Life 72°F (22°C) and 50% RH 1 year Durability / 1 year Time limits Must use it within 3 months after receiving the wrap film 3 months Shelf Life 1 year from date of purchase when stored at 50°F to 80°F (15°C – 25°C) and 45% to 50% relative humidity. Optimum recommended storage conditions are 72°F (22°C) and 50% relative humidity. Important Notice The physical properties of the product detailed in this document are based on tests that we believe to be reliable. They are intended only as a source of information and are given without guarantee. They do not constitute a warranty. Purchasers should independently assess the suitability of this material for their specific use prior to application. Warranty, Limited Remedy, and Disclaimer Unless an additional warranty is specifically stated on the applicable product packaging or literature, VinylFrog warrants that each product meets the applicable specifications at the time of shipment. We make no other warranties or conditions, express or implied, including but not limited to any implied warranty or condition of merchantability or fitness for a particular purpose, or any implied warranty or condition arising out of a course of dealing, custom, or usage of trade. If the VinylFrog product does not conform to this warranty, then based on our discretion, the sole and exclusive remedy is either the replacement of the product or a refund of the purchase price. Limitation of Liability Except where prohibited by law, VinylFrog will not be liable for any loss or damage arising from its product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. Durability The durability of the product is based on exposure conditions in South China. Actual performance life will depend on substrate preparation, exposure conditions, and maintenance of the product. For instance, in areas with excessively high temperature, industrial pollution, or high altitude, exterior performance will decrease. Recommendations Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, sprayer, towel, and installation liquidApplication method: Standard methods for Car Light Protection Film. Do not overstretch and overheat. Post heating is necessary.Post-heating temperature: 110°C flat surfaces, 130°C curves and overlaps.Aftercare: PH neutral. Avoid wax or solvents.