The "BADGER" 1/8 High-Speed Roughing CNC Router Bit, 1/8 Shank

<p data-mce-fragment="1">If you’ve experienced long carve times with your 1/8” bits, or even had them break because they cannot handle the workload, then get ready for this wicked little bit called the “<strong data-mce-fragment="1">BADGER</strong>”</p> <p data-mce-fragment="1">The <strong data-mce-fragment="1">BADGER</strong> has been called “<em><strong><span style="text-decoration: underline;">The little bit with a B</span><u data-mce-fragment="1">IG BITE</u></strong></em>”  by our fellow creators who tested it. For a 1/8” CNC router bit, no other 1/8” bit can match its aggressiveness and blazing speed for removing material from your CNC router project.</p> <p data-mce-fragment="1">With a 1/8 shank and 1/8” cut diameter, the <strong data-mce-fragment="1">BADGER</strong> falls into the roughing bit category. The <strong data-mce-fragment="1">BADGER</strong> is not designed to deliver clean cuts. Its sole purpose is speed, and it excels at it!</p> <p data-mce-fragment="1">Featuring a staggering 1/4" depth of cut per pass, 80ipm plunge rate, 70% step-over, and a whopping <strong data-mce-fragment="1"><u data-mce-fragment="1">130 inches per minute cut rate</u></strong>, the <strong data-mce-fragment="1">BADGER</strong> is undisputed when it comes to rapid material removal from your CNC router woodworking projects.</p> <p data-mce-fragment="1">Comparing to other 1/8” endmills, the BADGER can remove material 10X faster than standard 1/8” endmills</p> <p data-mce-fragment="1"><strong>Comparison Between the BADGER and Standard 1/8" Bits</strong></p> <table data-mce-fragment="1" height="204" width="407"> <tbody data-mce-fragment="1"> <tr data-mce-fragment="1"> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>Settings</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>Badger</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>Std. 1/8" Endmills</strong></p> </td> </tr> <tr data-mce-fragment="1"> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>Feed Rate  (Ipm)</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>130</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>50</strong></p> </td> </tr> <tr data-mce-fragment="1"> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>Depth Per Pass</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>0.25</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>0.0625</strong></p> </td> </tr> <tr data-mce-fragment="1"> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>Stepover</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>70%</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>40%</strong></p> </td> </tr> <tr data-mce-fragment="1"> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>Plunge Rate (ipm)</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>80</strong></p> </td> <td data-mce-fragment="1" style="width: 176.4px; text-align: center;"> <p data-mce-fragment="1"><strong>20</strong></p> </td> </tr> </tbody> </table> <p data-mce-fragment="1"> </p> <p data-mce-fragment="1">Getting a roughing bit like the <strong data-mce-fragment="1">BADGER </strong>is not just about time savings. It is also about saving your other 1/8” bits for the finishing touch-up AND prolonging the life of them.</p> <p data-mce-fragment="1">By using the <strong data-mce-fragment="1">BADGER</strong> as your workhorse for major material removal, you'll extend the lifespan of your regular CNC router bits. Let them handle the finishing touches while the <strong data-mce-fragment="1">BADGER</strong> handles the heavy lifting when a lot of material needs to be removed in fine details…like Aztec calendars.</p> <p data-mce-fragment="1">.</p> <p data-mce-fragment="1">HE-18-1</p>